Where to find drywall & framing bids in Washington DC: plan rooms and bid sources

Short answer: there is no single place to find drywall and framing bids in Washington, DC. The Office of Contracting and Procurement (OCP) publishes District solicitations and points new vendors to eSourcing, and the Department of General Services (DGS) lists active solicitations and capital construction projects. Private work mostly comes by invitation from general contractors. This page lists only the sources we could open and read.

Neighboring states: Maryland · Virginia

How public and private bids work in Washington DC

Public projects are advertised by the owner: a state agency, a city or county, a university or a school district. The bid notice, plans, specifications and addenda are normally posted on the owner's own site or plan room, and every project shows its bid date. Read each notice for bonding and registration terms.

Private projects are usually bid by invitation. A general contractor or owner decides who receives the documents, and the plans typically sit in a regional plan room, a bid service, or the GC's own portal. As a drywall, framing, insulation or CMU sub you usually price your scope to the GCs who are bidding, so being on the right planholder list matters.

Washington DC bid sources by type and region

Use the access column as a starting point, not a guarantee.

Not every Washington, DC owner is in this table. We did not find a Washington, DC AGC chapter page: the address we tried did not resolve, and the national AGC home page we opened did not list a DC chapter. We also did not get readable bid pages for GWU, Howard or UDC (UDC's home page had no procurement link), or for a builders exchange, so those are left out rather than guessed at. Also check Maryland and Virginia sources for the wider metro area.

Tips for subs

• Register as a planholder through the official channel. That is how you receive addenda, and some owners publish planholder lists that GCs use to find subs. Where a portal offers alerts by category or commodity code, turn them on.
• Go to the pre-bid meeting when there is one. Whether a meeting exists, and whether attendance is mandatory, is stated project by project in the notice. Read how scope is split between trades while you are there.
• Track addenda until bid day. Wall types, ceiling heights and scope can change, so reprice from the final set and re-check the day before the bid is due.
• Get the official set. Bid notices commonly say which plan room or design professional holds the controlling documents. Plans from another source may be incomplete.
• Check plan quality before you commit. Open the PDF and try to select a line or text. If you can, it is a vector file that can be measured exactly. If the page behaves like one picture, it is a scan and will take longer by hand. Also confirm the wall type legend is on the set; see what happens when it is missing.
• Check bonding and licensing before you price. Public notices often call for bid security and proof of licensing. Read the notice for the exact form.

Once you have the plans

ReadMyBlueprint is takeoff software, not a bid board. It reads vector plan sets for drywall, metal framing, wood framing, insulation and CMU. In our Freeport Square test (21 pages), 68.9% of walls were auto-matched and 99.8% after one "Confirm all." That was one plan set, so treat it as a single data point, and see the tour for how the review step works.

FAQ

Where do I find public construction bids in Washington, DC?

There is no single place. OCP publishes District solicitations, DGS lists active solicitations and capital construction projects, and DDOT links a contracting page. Universities run their own pages.

How do I register as a new vendor with the District?

The OCP page links New Vendor Registration through the District's eSourcing system. It does not give the steps; follow that link.

Is there one plan room or builders exchange for Washington, DC?

Our checks did not find a Washington, DC plan room or AGC chapter page we could read.

Can a subcontractor bid on Washington DC public projects?

Public owners advertise the prime contract, so subs normally price their scope to the general contractors who are bidding it. Read each bid notice for the owner's own rules, including any approved-bidder lists.

What is a planholder and why register as one?

A planholder is a firm that has officially requested the bid documents for a project. Registering usually puts you on the list that receives addenda, and some owners publish planholder lists that general contractors use to find subs. Download plans through the official channel, not from a forwarded link.

How are private bids different from public bids?

Public projects are advertised openly and the documents are usually posted on the owner's site. Private work is usually bid by invitation from a general contractor or owner, and documents come through a regional plan room, a bid service, or the GC directly. Access differs by source.

Does a scanned plan set matter when pricing a bid?

Yes. A vector PDF exported from CAD can be measured exactly, while a scanned plan is only a picture and has to be traced by hand or estimated. Check whether your plans are vector or scanned before you commit to a bid deadline.

Does ReadMyBlueprint list or sell bids?

No. ReadMyBlueprint is takeoff software, not a bid board. Once you have a plan set from any source above, you can upload it and review the takeoff yourself before the bid goes out.