For drywall subs and owner-estimators

Send us a Drywall plan set. We send back your counts.

Board, studs, track and insulation LF/SF by wall type, with every count traced to the wall it came from. Your first plan set is free, no card needed.

Updated October 2026

Continue — send my plan setFree first plan set · no card needed

See a real test first

Tested on a real 21-page set (Freeport Square Apartments): 68.9% of walls matched automatically, 99.8% after one "Confirm all".
Auto-takeoff can miss on sets it hasn't seen, so we check and hand-finish your counts before you get them. Anything uncertain is flagged for review.
First plan set free, no card needed. No call, no sales pitch.

Isometric illustration of a drywall panel being fastened to wood stud wall framing

How it works

How do you do a drywall takeoff from a PDF plan set?

Measure the real wall length

ReadMyBlueprint reads your plan's own printed scale and measures every partition and exterior wall directly from the vector geometry in your PDF — not an estimate, an actual measurement of the drawing.

Match it to a real wall type

Each wall's measured thickness is cross-referenced against the wall-type legend your architect already drew — telling ReadMyBlueprint whether it's single or double-layer board, and what stud type sits behind it.

Convert to a labeled sheet count

Wall length and height convert into a drywall sheet count for that wall type, shown next to the studs and track it goes with — labeled matched, ambiguous, or needs confirmation, never blended into one unlabeled number.

What it looks like

How is drywall counted by wall type?

Sheet counts aren't a separate, disconnected line — they're grouped with the wall assembly they belong to, so you can see exactly which walls drove the number.

Material summary — drywall & framing

2 1/2" steel stud @ 16" o.c.Matched

12,452 LF9,422 studs7,004 drywall sheets

2x6 wood stud @ 16" o.c.Matched

3,120 LF2,340 studs410 drywall sheets

Unspecified 4.4" partitionConfirm

86 LFsheet count needs wall-type confirmation

Being upfront

What can't automated drywall takeoff do?

Part of never presenting a guess as a measurement is telling you plainly where the line sits.

Not covered yet

Waste factor. Sheet counts are the raw quantity the geometry produces — you still apply your own waste percentage before it goes into a bid.
Tape, mud, corner bead, and fasteners. ReadMyBlueprint counts board, not finishing materials or hardware.
Fire-rating and acoustic assemblies beyond what's in your legend. If your plan set doesn't call out a UL assembly number or rating on the wall-type legend, ReadMyBlueprint can't infer one — that wall gets flagged for confirmation instead.
Scanned or flat-image PDFs. The measurement is only as real as the vector geometry it comes from — a scanned page has none to measure, so those pages are called out rather than guessed at.

See your own drywall count.

Upload your plan set and get a real, labeled sheet count in minutes. Your first plan set is free.

Continue — upload your plan Take the 2-minute tourFree first plan set · no card needed

Frequently asked questions

How does drywall takeoff software count sheets from a PDF?

It measures each wall from the vector geometry in your plan set, matches the wall to its type on your wall-type legend, then converts wall area into a labeled sheet count for both sides of the wall. On our Freeport Square test set (21 pages), 68.9% of walls auto-matched and 99.8% resolved after one "Confirm all". That is one test set, so uncertain walls are flagged for you to confirm.

What does drywall takeoff software not count?

Waste factor, tape, mud, corner bead and fasteners are not counted, and neither are fire-rated or acoustic assemblies the legend does not call out. Scanned or flat-image PDFs have no vector geometry to measure, so those pages are flagged.

Can I try it on my own plan set?

Yes. Your first plan set is free, no card needed.

Compare tools: ReadMyBlueprint vs. STACK & Bluebeam · Features · Take the tour